Search results

Broomvac:   As far as I know, this was a one time deal where the user was in a bind and needed his bathtub pumped out.   I also would not recommend anyone try this with their Kirby.   ~Stan  

Maybe you didn't have the carpet height adjustment set properly on the Kirby.   I assume the belt, brushroll and fan are in good condition?   Does the Kirby perform close to or better than the Rainbow when a brand new bag is installed?      

The Kirby shampoo brushroll is made of Hard Rubber and has sealed bearings so it is not affected by getting wet.   The fan chamber is completely sealed from the motor, so it is impossible for any liquid to get into the motor. If you search the archives on here, there is a story where someone...

Hi Edgar,   This is how you can get a great shine on all parts of your Legend II. I used this method on my Heritage Legend II seen in the photos below.   First, get a tube of Flitz polish from Amazon or Walmart. Flitz works better than Mother's and it also works on the plastic and rubber...

Mark:   I find that Odors Away fragrance to be quit pleasant.   I find that I need to add a few drops to my Kirby's inner bag about  once a week to keep it fresh smelling. Odors Away also keeps your house smelling nice too.  

I second David's opinion... I have been using "Odors Away" for years now. This stiff works wonders.   Just put a few drops on your newly installed cloth HEPA bag and that wonderful fragrance fills the room as you vacuum.   ~Stan  

Edgar: I hope this video will help you to tear down your Legend II and replace the switch if necessary.   Also, while you have it apart, you should replace the gray Lexan fan with a new white Amodel fan. The old Lexan fans are prone to crack and break apart causing damage to the fancase and...

Billy,   The DS50 had the lighted Kirby logo on the headlight cap for all 3 years of it's production. 1965 - 1967.   ~Stan      

FYI - Kirby didn't start using Amodel fans until the G5 came out.   Kirby G3 and G4 used the gray Lexan fans which tended to crack and break apart with age.   The link below will take you to an interesting article that describes how the Amodel fan came into being.  ...

Dual speed switch... Les,   The Kirby Diamond edition had a green speed switch located on top of the motor housing. This switch enabled the user to select a low speed mode to prevent the Kirby from sucking up small throw rugs which could stop the brushroll from spinning.   The Diamond...

Walter, Try to refrain from setting the Green Speed Switch on top of the motor housing to Low Speed which can cause the motor to overheat and burn out. This switch should always be set to High Speed.   The G7 Diamond was the only Kirby to have the 2 speed motor option. Kirby discontinued...

I am very proud to own this fully restored Heritage II Legend since 2015.   This and my Royal Everlast 8300 are my two favorite vacuums to use to clean my home.  

This also happened to me.   Try vacuuming with the headlight in the raised position. If the rattle stops, the the problem is with the headlight assembly.   To fix it just rotate the nozzle latch to the One O' Clock position and lower the headlight. This is what fixed my rattling problem...

As I was told by an old friend who worked for Kirby Corporate:   The current system will remain in place until Kirby can build a completely new system that can match or improve on the performance of the current Avalir system while remaining near the current price point. So far this has not...

You can use the new knurled belts (has tread on the inside instead of smooth) on all Kirby's from 513 to present Avalir as long as you have a Ball Bearing bushroll installed. The new knurled belt will ruin the older sleeve bearing brushrolls.    

CMBCOOL01:   Just curious, but hy did you buy a plastic vacuum knowing it is much more prone to breakage than your Kirby? If you needed another vacuum, why not just get another Kirby?   My brother had a Hoover Wind Tunnel Self Propelled and he had nothing but problems with it, especially...

Laura, That center divide on the bottom of the floor nozzle is the Belt Guard. It prevents the spinning belt from coming into contact with your carpet.   The handle does have a spring in it which will cause the handle to return to vertical position if you should let go of it.   That...

Thank you Les.   I am curious, why don't you like the BPI light?   ~Stan    

I love my 1988 Heritage II... I bought it in 2015 completely reconditioned and in brand new condition from a fellow collector. It has all of the attachments.   I prefer it over my Sentria for cleaning my house. It is quieter, lighter, more maneuverable and cleans my carpets as well or...

Actually...  A transformer with no load attached draws very little current. I found this statement on Wikipedia:   <span class="ILfuVd NA6bn"><span class="e24Kjd">"Since the secondary of the transformer is open, the primary draws only no-load current, which will have some copper loss. ...