Recent content by 3rdgenvacguy

VacuumLand – Vintage & Modern Vacuum Enthusiasts

Help Support VacuumLand:

  1. 3

    Early Hoovers, pumpers, Early Eureka -Columbus, Ohio

    Andy, I have the brush strips and parts, I am holding them for you. no worries. I do not have a hoover pn as pictured. Kirbycollector, I will hold them for you if you can get here this week, will give them to you. 235 N. 4th St. Columbus, Ohio 43215. downtown Columbus a block north of...
  2. 3

    Early Hoovers, pumpers, Early Eureka -Columbus, Ohio

    After 86 years our company is closing its doors. I have some machines that need some good homes. All will go cheap. Sorry, but working six days a week to clean out 4 floors of stuff. I have 2 Hoover 102's, 105, 541, 300 with red trim, 700, 725, 750, Eureka J,H, G2, kenkart, airway 55, coffee...
  3. 3

    Hoover Dialamatic issue

    transmission There are nylon gears in the transmission, however hardly ever fail. The shaft that runs through the unit where the pulley is has the same bearings used in each side as the agitator brush. If the black pulley spins fine with no play, they are probably O.K. There are two spools...
  4. 3

    Hoover Dialamatic issue

    Dial a Matic powerdrive The handle should slide back and forth and move the P.D. actuator bar. The bar must freely move to the left and right in order to engage the clutches in the self propell unit. There is a piece on the rear motor cover that the bar rest inside. If the bar rubs inside of...
  5. 3

    Hoover 61 Fan needed or sell vacuum

    Hoover 60 handle Both of my parts machines were model 61. I remember the 60 with the handle release at the top, but I no longer have any of those.
  6. 3

    Hoover 61 Fan needed or sell vacuum

    61 fan I tore down a couple machines, one had a chip in the fan. I did find a nice one. Price shipped would be $10. I would have to ship by usps, because I have been getting burned shipping by ups. my email is [email protected] Get me your address and I can give you my Paypal info if...
  7. 3

    Hoover 61 Fan needed or sell vacuum

    61 fan The fan on your 61 is different than a convertible fan. The center hub is taller, the fans linked above will not work. The fan you need is a part #21644 it fits the 29,60,61,62,63,64. The model 65 is the convertible fan part #22556 for the metal fan. I have some parts machines 60...
  8. 3

    Hoover 61 Fan needed or sell vacuum

    hoover 61 fan There are two screws that hold on the hood just behind the front wheels a ways. The headlight has a small regular screw and the motor has 4 screws. The fan pulley will unscrew clockwise or left hand thread.
  9. 3

    FQ 31, Eureka 1746A, and Eureka Cordaway!

    Brush rolls They had small pulley and large pulley brushes as well. Most wood I believe were the small pulley, The VG2 brush shown above is the large pulley. Notice the bottom plate has a bulge where the belt is covered. That is a sign that it used a large pulley brush. Trying to fit a...
  10. 3

    FQ 31, Eureka 1746A, and Eureka Cordaway!

    1746A brush assembly My distributor called back and confirmed that they have the 53412-1 brush roll in their Georgia warehouse. The brush cost me $27.93. I would have to pay shipping as well, so the price to you would be close to $40, then the shipping charges to you would be extra. You can...
  11. 3

    FQ 31, Eureka 1746A, and Eureka Cordaway!

    1746a brush That vacuum had a metal vg11 brush assembly part #53412-1. Sadly, it is no longer available. The lower end models also had a wooden brush assembly which also is no longer available. I checked with my distributor and they show one of the 53412-1 in their Georgia warehouse. They...
  12. 3

    Can anyone help me findling a certian Hoover Spring???

    agitator holder spring The spring that you need is not like a coil spring correct? It is more like a U shape bail spring. These are the same springs they use on the Hoover 28 and 29, and probably others. I have a parts diagram for the model 14, 28, and 29, The springs are all listed with...
  13. 3

    Miele 326i parts

    Miele s300 series dust channel The part is called the dust channel. It attaches under the lid with 4 screws. There are 3 or 4 tabs that break out, and the square piece ends of falling out the bottom. Part # for the S300 series is 04290592 suppose to list for just under 35 but most sell for...
  14. 3

    Plating on Upright Premier or Kenmore Vacs?

    I have the same premier duplex as yours, no chrome, no nickel. I think both of those machines have some strange oxidation on them. Did they both come from the same place? Almost like acid or something, however it is strange how uniform the oxidation is over the entire machine, and how nice...
Back
Top