Found a Super J in the basement
- Thread starter brewsky
- Start date
Help Support VacuumLand:
crazykirbydude
Well-known member
Nice find! You may want to get a new hose for it though. Those older Lux hoses can start to leak after a while.
lux_luthor
Well-known member
I recently bought a Super J from eBay and I was amazed how much power it has. The thing is older than me and where I’m used to modern vacuum motor sounds, I didn’t think it would perform as good. But it proved me wrong! I hooked up a 30ft hose, 2 wands, and a floor tool and it still was going strong and pulling in stuff before I passed over it. Definitely worth keeping and getting a new hose. The previous home owner left you a nice gift! =)
It will need a hose for sure...inside coils are loose.
Can't seem to find any info on taking this model apart for cleaning and lube if necessary?
which end does the motor come out of and how hard is it to stuff everything back in correctly?
Do bearings/bushings need lube or should I just use it as is?
Can't seem to find any info on taking this model apart for cleaning and lube if necessary?
which end does the motor come out of and how hard is it to stuff everything back in correctly?
Do bearings/bushings need lube or should I just use it as is?
vacman1961
Well-known member
Nice find, this is an early Super J, it came out late in 1975, you can tell because it has the PN2 power nozzle instead of the rug saver PN4 that was introduced in 1976, also the earlier Super J models had a white hose, the same color that was on the Golden Jubilee. In late 1977 going into 1978 the hose was gold colored and the machine came with a 5 year motor and fan warranty, due to issues with the earlier Super J armatures going bad prematurely. The Super j was the first year that the machine had a more powerful motor, on the steel all test the Super J picked up 4 steel balls as all the other previous models picked up 3.
rowdy141
Well-known member
Check a few posts lower-down on here. Francois has his Super-J apart. Difficulty getting the spring-assembly re-engaged. Perhaps you can shed light on his problem, as he yours?
real1shep
Well-known member
Depends on the end game. You have no investment so far, so you could run it till it dies. Or...you could take it apart and give it the spa treatment, attend to the motor bearings & brushes, buy a new hose for it and use it. Another option is to just attend to it mechanically and use it as your DD. I can't tell from the pics how much rust it has or if it's worth cleaning up.
The last of the great, strong Electrolux made two stage motors. The motor failures were limited to serials K____S only. A fire on the line caused Electrolux to outsource armatures for awhile which caused some motor failure. In promo literature the Super J actually picked up six steel balls.
Take phone pics of the wiring before you take the motor out.
Kevin
The last of the great, strong Electrolux made two stage motors. The motor failures were limited to serials K____S only. A fire on the line caused Electrolux to outsource armatures for awhile which caused some motor failure. In promo literature the Super J actually picked up six steel balls.
Take phone pics of the wiring before you take the motor out.
Kevin
quebecois
Well-known member
I bought two of them last week (10$ for the worst one and 25$ for the other), one has a couple of issues, including a weak cord rewinder I'm struggling fixing.
I'd also be interested to know how to gain access to the motor for cleaning and lubing, and try solving another issue (sort of gunpowder smell when it runs).
François
I'd also be interested to know how to gain access to the motor for cleaning and lubing, and try solving another issue (sort of gunpowder smell when it runs).
François
I found this thread with motor access instructions a few posts down:
http://www.vacuumland.org/cgi-bin/TD/TD-VIEWTHREAD.cgi?20611
http://www.vacuumland.org/cgi-bin/TD/TD-VIEWTHREAD.cgi?20611
quebecois
Well-known member
Thanks for the instructions. I just read them and I would suggest a small modification based on my recent work on this model.
Instructions are written like this : "The first thing you will need to do is to remove the top trim cover. It is held on by 3 screws--2 of which are located underneath the blower door. A third screw, usually phillips, is near the rear of the machine by the switch."
Actually, the third screw is not near the rear but near the front, by the door bag latch , on top of the trim cover.
I can't comment the rest of the text, I haven't been that deep in the machine yet.
Instructions are written like this : "The first thing you will need to do is to remove the top trim cover. It is held on by 3 screws--2 of which are located underneath the blower door. A third screw, usually phillips, is near the rear of the machine by the switch."
Actually, the third screw is not near the rear but near the front, by the door bag latch , on top of the trim cover.
I can't comment the rest of the text, I haven't been that deep in the machine yet.
real1shep
Well-known member
From the 1205 to the Diamond J, all the tanks come apart very similarly. Same with the cord winders, from the G to at least the Diamond J, they are all very much the same design with a few minor twists.
I have resisted in saying anything about the cord winder and taking down the Super J. It's best done with pics and I've never managed to be that organized.
DO take pics with your phone on all the wiring before you take the motor out. Also notice that there will be some sort of foam seal around the perimiter of the motor flange and you need to duplicate that foam with new when you reinstall the motor...unless it looks perfect. Many have put these back together ignoring this seal and had dismal vacuum.....and then passed the vac on to the next schlub. A good running Super J should pull at least 80".
Also, the auto bag/full opening device is kinda quirky to fix. Most of the time the diaphragm itself is OK, but the tubing is shot....there's a lot of tubing. You can get the tubing at a hardware store. If the tubing is loose enough to move easily where it's connected, it's causing problems with the design.
Kevin
I have resisted in saying anything about the cord winder and taking down the Super J. It's best done with pics and I've never managed to be that organized.
DO take pics with your phone on all the wiring before you take the motor out. Also notice that there will be some sort of foam seal around the perimiter of the motor flange and you need to duplicate that foam with new when you reinstall the motor...unless it looks perfect. Many have put these back together ignoring this seal and had dismal vacuum.....and then passed the vac on to the next schlub. A good running Super J should pull at least 80".
Also, the auto bag/full opening device is kinda quirky to fix. Most of the time the diaphragm itself is OK, but the tubing is shot....there's a lot of tubing. You can get the tubing at a hardware store. If the tubing is loose enough to move easily where it's connected, it's causing problems with the design.
Kevin
huskyvacs
Well-known member
My rule is to take it apart and clean and oil the motor if you plan to use it. You have no idea how long it's been down there and cool damp basements can wreck a vacuum's internals.
My usual rule is "if it ain't broke, don't fix it", as I sometimes end up breaking something in the process, especially with no manual or diagrams available!
But, in this case, you are probably right.
Trying to figure out how to remove the bottom chrome plate from the power nozzle (PN-2) without breaking or bending something! It seems to be stuck at the small slot on the back edge. It definitely needs to come apart!
But, in this case, you are probably right.
Trying to figure out how to remove the bottom chrome plate from the power nozzle (PN-2) without breaking or bending something! It seems to be stuck at the small slot on the back edge. It definitely needs to come apart!
real1shep
Well-known member
<a name="start_36174.388008"></a>"if it ain't broke, don't fix it"
Doesn't really work on vacs of this vintage....unless somebody in its recent history has gone through it. Since it's a basement find, I would assume it needs a restoration of the mechanicals at least. If you have a way to measure how much water lift it has, that will tell you a lot. Then when you turn off the motor, listen to it 'wind down'. It should spin free & easy without any unusual sounds and take awhile to stop.
Just corrosion & dirt holding that bottom PN plate.
Kevin
Doesn't really work on vacs of this vintage....unless somebody in its recent history has gone through it. Since it's a basement find, I would assume it needs a restoration of the mechanicals at least. If you have a way to measure how much water lift it has, that will tell you a lot. Then when you turn off the motor, listen to it 'wind down'. It should spin free & easy without any unusual sounds and take awhile to stop.
Just corrosion & dirt holding that bottom PN plate.
Kevin
human
Well-known member
PN2 bottom plate
Now that you have the screws out, just lift the plate from the side where you've drawn the red arrow. You may need to be firm with it, but it will come and you won't break anything. Once it's out, take the rollers out, flip it over and lift the cover off. You access the motor and belt from the top.
Now that you have the screws out, just lift the plate from the side where you've drawn the red arrow. You may need to be firm with it, but it will come and you won't break anything. Once it's out, take the rollers out, flip it over and lift the cover off. You access the motor and belt from the top.
real1shep
Well-known member
<a name="start_36174.388014"></a>I've got an old vacuum gauge (for cars) somewhere...or maybe I can rig up some tubing to test the lift.
Not sure that gauge will go high enough. If you can find a round ball that is solid, drill through and force a piece of metal tubing through it (use some sort of sealant between the tubing and the ball). Attach your gauge to one side and let the vac suck the ball on the other side. That's essentially a water lift gauge. You can buy them too.
Kevin
Not sure that gauge will go high enough. If you can find a round ball that is solid, drill through and force a piece of metal tubing through it (use some sort of sealant between the tubing and the ball). Attach your gauge to one side and let the vac suck the ball on the other side. That's essentially a water lift gauge. You can buy them too.
Kevin
vacman1961
Well-known member
The PN2 power nozzle comes apart through the top. Remove the 2 screws, flip it back over and take the top cover off. there is a bluish green cover that covers the brush roll. If you want to take the steel plate off there is an area in the top that you can unsnap that tab. It is not removable from the bottom, you will break it. Make a note that there is a new and worn side of the end bearings on the brush roll, this was the only Electrolux that had an adjustable brush roll as it wore out. Good luck.
